Accessories

  • Filter

Voltage Range: 0.25 to 30V rms Maximum Input Voltage: 30V rms, 200V dc AC to DC Ratio: 1:1 Ratio Accuracy (At 25 MHz and loaded with 10 M ohm) Above 0.5V: +/- 0.5 dB Below 0.5V: +/- 1.0 dB Add +/- 0.2 dB in RF fields of 1 to 3 V/m Frequency Response (Relative to 25 MHz): 100KHz to 100 MHz +/- 0.5 dB 100 MHz to 200 MHz +/- 2.0 dB 200 MHz to 500 MHz +/- 3.0 dB

Length: 1.2m (48”) Bandwidth: 12,5 MHz Maximum Signal Voltage: 600V rms. CAT III per IEC 1010-2-031 Maximum Voltage to Ground: 600V rms. CAT III per IEC 1010-2-031 Maximum Current: 1A

Replacement Test Lead Set For T5-600 and T5-1000 Electrical Testers

Patented TwistGuard extendable tip shroud that meets new electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements New WearGuard lead wire wear indicator. Each test lead is covered by two layers of silicone insulation; inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacement Double insulated silicone leads. TL175 withstands high temperatures and remains flexible in cold temperatures Extra-heavy strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure Universal input plugs compatible with all instruments that accept standard 4 mm shrouded banana plugs Probes always show correct category rating for tip exposure being used TL175E also available. Includes removable 4 mm lantern tips for versatility Conforms to EN61010-031 Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 Environmental ratings: -20 °C to 55 °C (-4 °F to 131 °F), altitude: 2000 m (6,562 ft) One-year warranty

Patented TwistGuard extendable tip shroud that meets new electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements New WearGuard lead wire wear indicator. Each test lead is covered by two layers of silicone insulation; inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacement Double insulated silicone leads. TL175 withstands high temperatures and remains flexible in cold temperatures Extra-heavy strain relief on both probe-end and plug-end, tested beyond 30,000 bends without failure Universal input plugs compatible with all instruments that accept standard 4 mm shrouded banana plugs Probes always show correct category rating for tip exposure being used TL175E also available. Includes removable 4 mm lantern tips for versatility Conforms to EN61010-031 Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 Environmental ratings: -20 °C to 55 °C (-4 °F to 131 °F), altitude: 2000 m (6,562 ft) One-year warranty

3 Test Leads connected to Low-Leakage Probes (red, black, green) 3 Alligator Clips (red, black, green) Maximum Jaw Opening: 26 mm (1 in.) Replacement Test Lead Set for the Fluke 1550B MegOhmMeter Length (Lead Only): 2.6 m (8.6 feet) Cat II 1000 V, Cat III 600 V, 5kV DC Max (Probes) Cat II 1000 V, Cat III 600 V, 20 amps (Alligator Clips)

Test Leads connected to Low-Leakage Probes(red, black, green) 3 Alligator Clips (red, black, green) Maximum Jaw Opening: 26 mm (1in) Replacement Test Lead Set for the Fluke 1550B/1550C/1555 MegOhmMeter Cat II 1000 V, Cat III 600 V, 5kV DC Max (Probes) Cat II 1000 V, Cat III 600 V, 20 amps (Alligator Clips) Test Leads extend to 25ft!

DMM test leads (red, black) with safety shrouded, standard diameter banana plugs Right angle connector on both ends Reinforced strain relief 1.5 meter silicone-insulated wire resists heat & cold CAT IV 600 V, CAT III 1000 V, 10 A rating. UL listed One year warranty